Advanced Elasto coat

“HYBRID PREMIUM ACRYLIC LIQUID MEMBRANE”

Bulwark Elasto coat is single component, Premium Hybrid Acrylic Membrane which is consists of specially developed polymers and properly selected components. Bulwark Elasto coat is not a usual elastomeric coating unlike other elastomeric coating Bulwark Elasto coat made by using Pure Acrylic Resin and Modified Kaolin which ensure long lasting performance. It cures by natural air, sunlight and gives elastomeric waterproof membrane BULWARK ELASTO COAT is elastomeric in nature and has good resistance to weather and sunlight.

BULWARK ELASTO COAT has excellent protection against UV rays and reduces the temperature of 8°C –13°C It possess breathing properties, water resistance, crack bridging properties & UV resistance.

AREA OF APPLICATION :

Wherever water proofing need with high elongation
Open Terrace and
Any Open Surfaces
On Metal Roof
Exterior Side Walls

FEATURES: :

Will Provide Flexible water proof membrane.
Allows trapped vapor to escape thus preventing peeling and blistering.
Can be applied in uniform thickness to horizontal and vertical surfaces.
Develops excellent bond to most building materials.
BULWARK ELASTO COAT is not affected by ultraviolet light or by chemicals ranging from mild acids to strong alkalis.
BULWARK ELASTO COAT is non-flammable and does not give off toxic gases.
BULWARK ELASTO COAT is not harmful to the health of workman.

METHOD OF APPLICATION WATER PROOFING COATING:

(I) SURFACE PREPARATION

Prior to application of BULWARK ELASTO COAT the surface must be prepared as mentioned below to avoid failure and to achieve maximum beneficial properties.
When placing BULWARK ELASTO COAT coating, water should be removed so that surface is only damp. In no case there should be standing water.
The surface shall be cleaned to remove all dust, foreign matters, loose materials or any deposits of contamination which could affect the bonding.
In Terrace Identify the poor slope area /water stagnation area by mark the same then apply one coat of bulwark seal cote 3 and two coats of bulwark PU 300 in those area alone orelse application may meet failure.

(II) Application:

After surface preparation like Removing loose particles and crack Treatment BULWARK ELASTO COAT must be applied on the Top of BULWARK PSC OR SEAL COTE 3 OR LEAK BOND II
Two coats are recommended one more coat can be done to achieve desired thickness.
First coat should be allowed to air dry for 2-3 hours prior to apply subsequent coat.
If pond test to be done then can be done only after 48 hrs from the time of application.

PRECAUTIONS:

BULWARK ELASTO COAT system must be applied with temperature above 2⁰ C and below 40⁰ C.
BULWARK ELASTO COAT should not be used with addition of cement.
BULWARK ELASTO COAT is not harm for applicators and users.
If cement primer then strictly Bulwark Elasto coat must be applied after 24hrs orelse application may meet failure.
There must be 4 hours gap between subsequent coat orelse application may meet failure.

STORAGE:

Store in dry cool place in the temperature range from 5⁰C to 30⁰C in sealed condition.
Do not allow to freeze. Keep away from direct sunlight.

AVAILABLE COLOUR:

White, Terra cotta and Grey

PACKAGING:

10 Kg, 20 kg

TECHNICAL DATA:

PARAMETERS	TEST VALUE	METHOD
Appearance	White but Tintable	Visual
Elongation	380% ± 40	ASTM D 412
Water Penetration Test @ 3 bar	No Penetration	DIN1048:PT5:91
Accelerated weather resistance	Passes the test	ASTMG154
Crack Bridging ability	No crack at 2mm gap	ASTM D2240:91
Solid Content	62+-2	IS STD TEST
Abrasion /Hardness	High	ASTMD240:2002
Adhesive Strength	2.1N/mm²	ASTM D3359
Algae & Fungus Resistant	High ( No Growth)	(ss 345:1998)
Recoating Time, at 27ᴼC, 65% RH, HOURS	03-04 hours	IS 101
Full Cure	2 DAYS	IS 101
Consistency	5-10 % Potable water	IS 101
Volatile organic Matter (VOC) %, (w/w)	<0.8 %	IS 101
SRI (White Base)	110 ±5	ASTM E1980
Thickness	900Microns ±200 wet film thickness	ASTM D 1640

COVERING CAPACITY:

Bulwark Elasto coat will give following coverage in below mentioned surface
Coverage will vary based on surface, Application type and workmanship.
Adding more water may give more coverage but definitely affect the quality.
To achieve desired thickness along with good coverage better use appropriate level of water i.e. Not more than 5-10% of the Bulwark Elasto coat volume.

SURFACE	COVERAGE/KG
COUNTRY TILES	2- 2.2 S.QM FOR TWO COATS
CEMENT FLOOR	1.7- 2 S.QM FOR TWO COATS
VERTICAL WALL	2- 2.3 S.QM FOR TWO COATS

SHELF LIFE & STORAGE:

SHELF LIFE IS 12 MONTHS FROM THE DATE OF MANUFECTURING.

IMPORTANT NOTE:

All BULWARK CHEMICALS and its products are sold in the market after strict Quality Control in line of ISO 9001 and guaranteed against any manufacturing defect. Although the basic formulation of Company’s products generally remains unchanged, production refinements arising from continuing research and evaluation program may occasionally result in marginal changes in properties. Bulwark aspires to ensure that any recommendation, advice, test data, specification, method statement and other information given in this product datasheet is accurate and best of company’s knowledge. Since, the company (bulwark cool coats and chemicals) has no control over the selection of its product, applicators, application methodology, how and where it is applied, therefore, the company cannot accept any liability directly or indirectly arising from the use of its product. It is important to any customer; user or specifier satisfies him / herself that the product is suitable for the intended purpose including health, safety and environmental aspect. Unless or otherwise agreed in writing, all products of the company are sold strictly pursuant to the terms of our standard conditions of sale which are available upon request. All information and technical assistance is given without warranty or guarantee and is subject to change without notice. All customers, users, specifiers should ensure that they examine the suitability of the product with company’s latest product data sheet.

CUSTOMER CARE : 1800 88 921 88