BULWARK LEAK BOND-III is highly flexible premium Acrylic concrete protective coating for concrete it is two component premium grade liquid rubber with composition of Acrylic modified co polymer and Cement based fine granules, It cures by sunlight and good air circulation and will give a tough flexible membrane.BULWARK LEAK BOND-III has excellent bonding with concrete, water resistance, with crack bridging properties this can be applied on any area wherever require heavy duty, high water resistant coating and before laying Tiles, marble and granite to prevent water ingress and alleviates staining.
AREA OF APPLICATION:
- On any Concrete slab i.e. sunken slab, Roof slab
- Can be applied on swimming pool and water tank.
- Wherever need heavy duty water proofing and protective membrane.
- For Potable water tank use “ Bulwark Seal Cote 3 ( Food Grade)
FEATURES:
- Will Provide Tough, Flexible water proof membrane.
- Can be applied in uniform thickness to horizontal and vertical surfaces
- Develops excellent bond to most building materials.
- BULWARK LEAK BOND–III is highly durable in continuous wet condition.
- BULWARK LEAK BOND-III is non-flammable and does not give off toxic gases, when exposed to fire,
- BULWARK LEAK BOND–III is not harmful to the health of workman.
METHOD OF APPLICATION IN WATER PROOFING :
SURFACE PREPARATION:
- Prior to application of BULWARK LEAK BOND-III the surface must be prepared as mentioned below to avoid failure and to achieve maximum beneficial properties.
- When placing BULWARK LEAK BOND-III coating, water should be removed so that surface is only damp. In no case there should be standing water.
- In sunken corner area must to be packed with Bulwark cement Mortar prior to this application.
- All concrete surfaces shall be thoroughly pre-wetted prior to the application of “BULWARK LEAK BOND-III” coating by sprinkle water on flat surface.
APPLICATION:
- BULWARK LEAK BOND-III must be mixed with in the ratio of 1:3 (PART A: PART B) 5-10% water can be added on total weight for brushable consistency.
- The mix has to be stirred thoroughly until smooth homogeneous slurry is obtained. Wait for 1-3 minutes to release entrapped air bubbles.
- Two are recommended one more coat can be done to achieve desired thickness.
- First coat should be allowed to air dry for 3-4 hours prior to apply subsequent coat.
PRECAUTIONS:
- BULWARK LEAK BOND-2 system must be applied with temperature above 5⁰ C and below 40⁰ C.
- Pour out Part B slowly on Part A and use slow speed stirrer to mix thoroughly.
- Use BULWARK LEAK BOND-III when expectation is high flexibility and high water resistance.
STORAGE:
- Store in dry cool place in the temperature range from 5⁰C to 30⁰C in sealed condition.
- Do not allow to freeze. Keep away from direct sunlight.
PACKAGING:
- 20Kg Pack (Part A 5Kg +Part B 15Kg Powder)
TECHNICAL DATA:
| PARAMETERS | TEST VALUE | METHOD |
|---|---|---|
| APPEARANCE (PART A) | MILK WHITE FREE FLOW LIQUID | VISUAL |
| POT LIFE ( MIXED SLURRY) | 55 Mins | AT 25oC |
| THICKNESS AFTER TWO COATS | 0.9-1 MM | ASTM |
| ELONGATION AT BREAK | 50%-60% | ASTM D 412 |
| CRACK BRIDGE ABILITY | 0.9MM – 1MM | ASTM C 836 |
| APPEARANCE (PART B) | POWDER | VISUAL |
| VISCOSITY PER SECONDS (PART A) | 11 +-1 | IS 101 |
| SOLID CONTENT (PART A) | 55% +-2 (W/W) | IS 101 |
| PH VALUE (PART A) | > 7 | IS 9103 |
| ADHESION ON CONCRETE ON 7TH DAY | 1.68 N/mm2 | ASTM D 4541 |
COVERING CAPACITY:
- BULWARK LEAK BOND-III will give following coverage in below mentioned surface
- Coverage will vary based on mixing ratio, surface, Brush type and workmanship.
- Adding more water may give more coverage but definitely affect the quality.
| SURFACE | COVERAGE/KG |
|---|---|
| CONCRETE | 14-16 S.QM FOR TWO COATS |
| PLASTERED CEMENT FLOOR | 16-18 S.QM FOR TWO COATS |
IMPORTANT NOTE :
All BULWARK CHEMICALS and its products are sold in the market after strict Quality Control in line of ISO 9001 and guaranteed against any manufacturing defect. Although the basic formulation of Company’s products generally remains unchanged, production refinements arising from continuing research and evaluation program may occasionally result in marginal changes in properties. Bulwark aspires to ensure that any recommendation, advice, test data, specification, method statement and other information given in this product datasheet is accurate and best of company’s knowledge. Since, the company (bulwark cool coats and chemicals) has no control over the selection of its product, applicators, application methodology, how and where it is applied, therefore, the company cannot accept any liability directly or indirectly arising from the use of its product. It is important to any customer; user or specifier satisfies him / herself that the product is suitable for the intended purpose including health, safety and environmental aspect. Unless or otherwise agreed in writing, all products of the company are sold strictly pursuant to the terms of our standard conditions of sale which are available upon request. All information and technical assistance is given without warranty or guarantee and is subject to change without notice. All customers, users, specifers should ensure that they examine the suitability of the product with company’s latest product data sheet.
CUSTOMER CARE : 1800 88 921 88